2MELM74W8SX630182

Dorman Products, Inc. (Dorman) is recalling certain model Dorman Steering Shafts, part number 425-359, Solutions Steering Shafts, part number 7-0359, and OE Solutions Steering Shafts, part number 425-359, manufactured April 17, 2014, to September 28, 2015. These aftermarket replacement steering shafts are sold for use in 1995-2002 Ford Crown Victoria, Mercury Grand Marquis, and Lincoln Town Car vehicles. These steering shafts may separate during operation if the integral fastener is loose or missing and if the interfacing vehicle shaft is compressed in length.

If the shafts separate during vehicle operation, a loss of steering control would result, increasing the risk of a vehicle crash.

Dorman will notify owners, and dealers will replace the steering shaft, free of charge. The recall began on October 28, 2015. Owners may contact Dorman customer service at 1-800-523-2492, option 5.

FORD IS RECALLING 225,000 MY 1992-2003 ECONOLINE, MY 1993-1995 TAURUS SHO, MY 1992-1998 CROWN VICTORIA, MY 1993 BRONCO, F-SERIES, MY 1995-1997 F-SERIES SUPER DUTY STRIPPED CHASSIS, MY 1992-1998 MERCURY GRAND MARQUIS, AND MY 1992-1995 LINCOLN TOWN CAR VEHICLES. THE AFFECTED VEHICLES WERE PREVIOUSLY REPAIRED USING A WIRING HARNESS THAT IS NOT COMPATIBLE WITH THE VEHICLE CIRCUIT POLARITY.

AS A RESULT, THE FUSE IS LOCATED IN THE OUTPUT CIRCUIT RATHER THAN IN THE INTENDED INPUT POWER FEED CIRCUIT, AND MAY NOT OFFER THE INTENDED PROTECTION IN THE EVENT OF AN ELECTRICAL SHORT TO GROUND.

DEALERS WILL INSTALL A NEW WIRING HARNESS, OR REPLACE THE MATING ELECTRICAL COMPONENT. THE RECALL BEGAN ON FEBRUARY 18, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

THIS COULD RESULT IN AN UNDERHOOD FIRE.

DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

THE PASSENGER SIDE AIR BAG HAS AN INFLATOR BODY THAT CRACKED DURING FORMING OF THE CURL THAT RETAINS THE IGNITER PLUG IN THE END OF THE INFLATOR. ALSO THE IGNITER END CAP CAN SEPARATE FROM THE INFLATOR.

THE PASSENGER SIDE AIR BAG MAY NOT INFLATE PROPERLY RESULTING IN REDUCED OCCUPANT PROTECTION IN A VEHICLE ACCIDENT. IF THE IGNITER END CAP SEPARATES IN A FRONTAL COLLISION, HOT GASES CAN BE RELEASED AND IGNITE FLAMMABLE MATERIAL OR CAUSE BURN INJURIES.

DEALERS WILL REMOVE AND REPLACE THE PASSENGER SIDE AIR BAG MODULE.

THE RIVETS HOLDING THE REAR OUTBOARD BELT D-RINGS WERE NOT HEAT TREATED PROPERLY CAUSING THE HEADS OF THE RIVETS TO FRACTURE UNDER LOAD AND FAIL TO HOLD THE D-RINGS TO THE STRAPS. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."

CONSEQUENCE OF NON-COMPLIANCE: THIS CONDITION CAN REDUCE THE RESTRAINING CAPABILITIES OF THE SAFETY BELT IN THE EVENT OF AN ACCIDENT.

DEALERS WILL INSTALL A REINFORCEMENT PLATE ON THE REAR OUTBOARD SEAT BELT ASSEMBLY ANCHORAGES INVOLVED IN THIS CAMPAIGN.

THESE VEHICLES WERE BUILT WITH THE NON-CYCLING POWER WINDOW CIRCUIT BREAKER AND THE CYCLING HEADLAMP CIRCUIT BREAKER INTERCHANGED.

IN THE EVENT OF A SHORT OR OVERLOAD IN THE HEADLAMPCIRCUIT, BOTH HEADLAMPS CAN GO OUT WITHOUT WARNING, RATHER THAN FLASHING AS INTENDED WITH THE CYCLING CIRCUIT BREAKER. THIS COULD LEAD TO REDUCED NIGHT TIME DRIVER VISIBILITY, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

DEALERS WILL INSPECT THESE VEHICLES, REMOVE THE CIRCUIT BREAKER AND REINSTALL THE BREAKER IN THE CORRECT LOCATIONS.

THE SEAL MATERIAL BETWEEN THE FUEL FILLER PIPE AND FUEL TANK MAY NOT HAVE BEEN FULLY CURED DURING THE MOLDING PROCESS WHICH COULD ALLOW FOR FUEL LEAKAGE.

FUEL LEAKAGE COULD RESULT IN A VEHICLE FIRE IF AN IGNITION SOURCE WERE PRESENT.

DEALERS WILL REPLACE THE FUEL FILLER PIPE-TO-FUEL TANK SEAL WITH A NEW SEAL OF DIFFERENT MATERIAL.